This report would have more information with
"Show verbose output during compilation"
enabled in File > Preferences.
Arduino: 1.0.6 (Windows 7), Board: "ATtiny85 (internal 8 MHz clock)"
c:/program files (x86)/arduino/hardware/tools/avr/bin/../lib/gcc/avr/4.3.2/../../../../avr/lib/avr25/crttn85.o:(.init9+0x2): relocation truncated to fit: R_AVR_13_PCREL against symbol `exit' defined in .fini9 section in c:/program files (x86)/arduino/hardware/tools/avr/bin/../lib/gcc/avr/4.3.2/avr25\libgcc.a(_exit.o)
ds18b20_ctc_attiny85.cpp.o: In function `loop':
C:\Program Files (x86)\Arduino/ds18b20_ctc_attiny85.ino:44: relocation truncated to fit: R_AVR_13_PCREL against symbol `__gesf2' defined in .text.fplib section in c:/program files (x86)/arduino/hardware/tools/avr/bin/../lib/gcc/avr/4.3.2/../../../../avr/lib/avr25\libm.a(gesf2.o)
[syntax=cpp]#include <OneWire.h>
#include <DallasTemperature.h>
#define ledPin 4
// Data wire is plugged into pin 7 on the Arduino
#define ONE_WIRE_BUS 3
// Setup a oneWire instance to communicate with ANY OneWire devices
OneWire oneWire(ONE_WIRE_BUS);
// Set oneWire reference to Dallas Temperature sensor.
DallasTemperature sensors(&oneWire);
void CTC_init();
void setup()
{
pinMode(ledPin, OUTPUT);
sensors.begin();
// initialize timer1
noInterrupts(); // disable all interrupts
TCCR0A = 0;
TCCR0B = 0;
TCNT0 = 0;
interrupts(); // enable all interrupts
}
ISR(TIMER0_COMPA_vect) // timer compare interrupt service routine
{
digitalWrite(ledPin, digitalRead(ledPin) ^ 1); // toggle LED pin
}
void loop()
{
CTC_init();
sensors.requestTemperatures();
int n;
n = ((sensors.getTempCByIndex(0)) + 60); //przesuniecie dla temp -55*C aby uzyskac wartosci tylko dodatnie
if ((sensors.getTempCByIndex(0)) >= -50)
{
OCR0A=n; //przypisanie OCR1A wartosci temperatury
}
else
{
OCR0A=31249; //jesli przekracza zakres to generuje 1Hz
}
}
void CTC_init()
{
TCCR0A |= (1 << WGM01); // CTC mode
TCCR0B |= (1 << CS02); // 256 prescaler
TIMSK |= (1 << OCIE0A); // enable timer compare interrupt
}[/syntax]
Może go ktos sprawdzuc u siebie?
A teraz mam taki blad
C:\Program Files (x86)\Arduino\libraries\OneWire\OneWire.cpp: In constructor 'OneWire::OneWire(uint8_t)':
C:\Program Files (x86)\Arduino\libraries\OneWire\OneWire.cpp:123: error: 'digitalPinToBitMask' was not declared in this scope
C:\Program Files (x86)\Arduino\libraries\OneWire\OneWire.cpp:124: error: 'digitalPinToPort' was not declared in this scope
C:\Program Files (x86)\Arduino\libraries\OneWire\OneWire.cpp:124: error: 'portInputRegister' was not declared in this scopeStatystyki: Napisane przez endurasek — 7 gru 2014, o 15:26
]]>