ATNEL tech-forum 2016-10-04T14:32:28+01:00 https://forum.atnel.pl/feed.php?f=46&t=16380&mode 2016-10-04T14:32:28+01:00 2016-10-04T14:32:28+01:00 https://forum.atnel.pl/viewtopic.php?t=16380&p=170400#p170400 <![CDATA[Re: Atollic TrueStudio implementacja własnej biblioteki lcd]]>

Tak dla potomnych

Plik LCD.c:

[syntax=c]/*
* HAL_LCD_NOKIA.c
*
* Created on: Oct 3, 2016
* Author: KosteQ
*/

#include "stm32f4xx_hal.h"
#include "HAL_LCD_NOKIA.h"


const unsigned char font[] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5f,0x00,0x00,0x00,0x00,0x07,0x00,0x07,
0x00,0x00,0x14,0x7f,0x14,0x7f,0x14,0x00,0x24,0x2a,0x7f,0x2a,0x12,0x00,0x23,0x13,
0x08,0x64,0x62,0x00,0x36,0x49,0x55,0x22,0x50,0x00,0x00,0x00,0x03,0x00,0x00,0x00,
0x00,0x1c,0x22,0x41,0x00,0x00,0x00,0x41,0x22,0x1c,0x00,0x00,0x14,0x08,0x3e,0x08,
0x14,0x00,0x08,0x08,0x3e,0x08,0x08,0x00,0x00,0x50,0x30,0x00,0x00,0x00,0x08,0x08,
0x08,0x08,0x08,0x00,0x00,0x60,0x60,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x00,
0x3e,0x51,0x49,0x45,0x3e,0x00,0x00,0x42,0x7f,0x40,0x00,0x00,0x42,0x61,0x51,0x49,
0x46,0x00,0x21,0x41,0x45,0x4b,0x31,0x00,0x18,0x14,0x12,0x7f,0x10,0x00,0x27,0x45,
0x45,0x45,0x39,0x00,0x3c,0x4a,0x49,0x49,0x30,0x00,0x03,0x71,0x09,0x05,0x03,0x00,
0x36,0x49,0x49,0x49,0x36,0x00,0x06,0x49,0x49,0x29,0x1e,0x00,0x00,0x36,0x36,0x00,
0x00,0x00,0x00,0x56,0x36,0x00,0x00,0x00,0x08,0x14,0x22,0x41,0x00,0x00,0x14,0x14,
0x14,0x14,0x14,0x00,0x00,0x41,0x22,0x14,0x08,0x00,0x02,0x01,0x51,0x09,0x06,0x00,
0x32,0x49,0x79,0x41,0x3e,0x00,0x7e,0x11,0x11,0x11,0x7e,0x00,0x7f,0x49,0x49,0x49,
0x36,0x00,0x3e,0x41,0x41,0x41,0x22,0x00,0x7f,0x41,0x41,0x41,0x3e,0x00,0x7f,0x49,
0x49,0x49,0x41,0x00,0x7f,0x09,0x09,0x09,0x01,0x00,0x3e,0x41,0x41,0x49,0x7a,0x00,
0x7f,0x08,0x08,0x08,0x7f,0x00,0x00,0x41,0x7f,0x41,0x00,0x00,0x20,0x40,0x41,0x3f,
0x01,0x00,0x7f,0x08,0x14,0x22,0x41,0x00,0x7f,0x40,0x40,0x40,0x40,0x00,0x7f,0x02,
0x0c,0x02,0x7f,0x00,0x7f,0x04,0x08,0x10,0x7f,0x00,0x3e,0x41,0x41,0x41,0x3e,0x00,
0x7f,0x09,0x09,0x09,0x06,0x00,0x3e,0x41,0x51,0x21,0x5e,0x00,0x7f,0x09,0x19,0x29,
0x46,0x00,0x46,0x49,0x49,0x49,0x31,0x00,0x01,0x01,0x7f,0x01,0x01,0x00,0x3f,0x40,
0x40,0x40,0x3f,0x00,0x1f,0x20,0x40,0x20,0x1f,0x00,0x3f,0x40,0x38,0x40,0x3f,0x00,
0x63,0x14,0x08,0x14,0x63,0x00,0x07,0x08,0x70,0x08,0x07,0x00,0x61,0x51,0x49,0x45,
0x43,0x00,0x00,0x7f,0x41,0x41,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x00,0x00,0x41,
0x41,0x7f,0x00,0x00,0x04,0x02,0x01,0x02,0x04,0x00,0x40,0x40,0x40,0x40,0x40,0x00,
0x00,0x01,0x02,0x04,0x00,0x00,0x20,0x54,0x54,0x54,0x78,0x00,0x7f,0x48,0x44,0x44,
0x38,0x00,0x38,0x44,0x44,0x44,0x20,0x00,0x38,0x44,0x44,0x48,0x7f,0x00,0x38,0x54,
0x54,0x54,0x18,0x00,0x08,0x7e,0x09,0x01,0x02,0x00,0x18,0xa4,0xa4,0xa4,0x7c,0x00,
0x7f,0x08,0x04,0x04,0x78,0x00,0x00,0x48,0x7d,0x40,0x00,0x00,0x00,0x00,0x84,0x7d,
0x00,0x00,0x7f,0x10,0x28,0x44,0x00,0x00,0x00,0x41,0x7f,0x40,0x00,0x00,0x7c,0x04,
0x78,0x04,0x78,0x00,0x7c,0x08,0x04,0x04,0x78,0x00,0x38,0x44,0x44,0x44,0x38,0x00,
0xfc,0x24,0x24,0x24,0x18,0x00,0x18,0x24,0x24,0x28,0xfc,0x00,0x7c,0x08,0x04,0x04,
0x08,0x00,0x48,0x54,0x54,0x54,0x20,0x00,0x04,0x3f,0x44,0x40,0x20,0x00,0x3c,0x40,
0x40,0x20,0x7c,0x00,0x1c,0x20,0x40,0x20,0x1c,0x00,0x3c,0x40,0x30,0x40,0x3c,0x00,
0x44,0x28,0x10,0x28,0x44,0x00,0x1c,0xa0,0xa0,0xa0,0x7c,0x00,0x44,0x64,0x54,0x4c,
0x44,0x00,0x00,0x08,0x36,0x41,0x00,0x00,0x00,0x00,0x7f,0x00,0x00,0x00,0x00,0x41,
0x36,0x08,0x00,0x00,0x10,0x08,0x08,0x10,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x20,0x54,0x54,0xd4,0x78,0x00,0x38,0x44,0x46,0x45,0x20,0x00,0x38,0x54,0x54,0xd4,
0x18,0x00,0x00,0x49,0x7f,0x44,0x00,0x00,0x7c,0x08,0x06,0x05,0x78,0x00,0x38,0x44,
0x46,0x45,0x38,0x00,0x48,0x54,0x56,0x55,0x20,0x00,0x44,0x64,0x56,0x4d,0x44,0x00,
0x44,0x64,0x55,0x4c,0x44,0x00,0x7e,0x11,0x11,0x91,0x7e,0x00,0x3c,0x42,0x46,0x43,
0x24,0x00,0x7f,0x49,0x49,0xc9,0x41,0x00,0x7f,0x50,0x48,0x44,0x40,0x00,0x7e,0x04,
0x0b,0x10,0x7e,0x00,0x3c,0x42,0x46,0x43,0x3c,0x00,0x4c,0x52,0x56,0x53,0x22,0x00,
0x42,0x66,0x53,0x4a,0x46,0x00,0x42,0x62,0x53,0x4a,0x46,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};


void lcd_init(void){


LCD_RST_CLR;
HAL_Delay(20);
LCD_RST_SET;
LCD_CE_SET;
lcd_write_byte(LCD_CMD, 0x21); // Function set - extended instruction set
lcd_write_byte(LCD_CMD, 0x13); // Bias - 1:48
lcd_write_byte(LCD_CMD, 0x06); // Temperature Control
lcd_write_byte(LCD_CMD, 0xa5); // Set Vop
lcd_write_byte(LCD_CMD, 0x20); // Function set - basic instruction set, horizontal addressing
lcd_write_byte(LCD_CMD, 0x0C); // Display control - normal mode
}

void lcd_write_byte(unsigned char c_d, unsigned char data ){
unsigned char m;
LCD_CE_CLR;

if(c_d) LCD_DC_SET; else LCD_DC_CLR;

for(m=0x80; m; m>>=1)
{
if(data & m)
LCD_DATA_SET;
else
LCD_DATA_CLR;

LCD_CLK_SET;
for(int i=0; i<200; i++){

}
LCD_CLK_CLR;
}
LCD_CE_SET;
}

void lcd_image(const unsigned char s[],char x, char y, char w, char h){
unsigned int i,j,k;

for(i=0,j=0,k=0; i<h; i++)
{
lcd_write_byte(LCD_CMD, 0x40|(i+y));
lcd_write_byte(LCD_CMD, 0x80|(x));

for(j=0; j<w ; j++,k++){
lcd_write_byte(LCD_DATA, (s[k]));
}
}
}

void lcd_text(char s[], unsigned char x, unsigned char y)
{
unsigned int c,j;
unsigned char i,k;

// Kody polskich literek z ogonkami
char pl[] = {'ą','ć','ę','ł','ń','ó','ś','ź','ż','Ą','Ć','Ę','Ł','Ń','Ó','Ś','Ź','Ż'};

// Ustawia położenia pierwszej litery tekstu na ekranie LCD
lcd_write_byte(LCD_CMD, LCD_SETY|(y));
lcd_write_byte(LCD_CMD, LCD_SETX|(x));

// Rysuje znak po znaku
for(k=0; (c = s[k]); k++)
{
// Dopasowuje kody znaków z ogonkami
for(i=0; (i<18) && (pl[i]!=c); i++) ;
if(i<18) c= 0x80+i;

// Kopiuje jeden znak(6x8) z FLASH do pamięci obrazu LCD
for(i=0, j=(c-32)*6; i<6; i++,j++)
lcd_write_byte(LCD_DATA, (font[j]));
}
}

void lcd_clear(void){
unsigned char i,j;

LCD_HOME;

for(i=0; i<LCD_Y; i++)
{
LCD_GOTO(0, i);
for(j=0; j<LCD_X; j++)
lcd_write_byte(LCD_DATA, 0x00);
}

LCD_HOME;
}

void lcd_scroll(unsigned char txt[], unsigned char line, unsigned int czas)
{
unsigned int j,l,k,n,m;
unsigned char c,i;

// Kody polskich literek z ogonkami
unsigned char pl[] = {'ą','ć','ę','ł','ń','ó','ś','ź','ż','Ą','Ć','Ę','Ł','Ń','Ó','Ś','Ź','Ż'};

// liczenie znaków w tekście
for(n=0;(txt[n]);n++);

for(j=0; j<(n-(LCD_X/6))*6 ;j++)
{
LCD_GOTO(0, line);

for(i=0,l=j; i<LCD_X ;i++,l++)
{
c = (txt[ (l/6) ]);

// Dopasowuje kody polskich znaków z ogonkami
for(m=0; (m<18) && (pl[m]!=c); m++) ;
if(m<18) c= 0x80+m;

k = (c-32)*6+(l%6);

lcd_write_byte(LCD_DATA, (font[k]));
}
HAL_Delay(czas);
}
}[/syntax]

LCD.h:

[syntax=c]/*
* HAL_LCD_NOKIA.h
*
* Created on: Oct 3, 2016
* Author: KosteQ
*/

#ifndef HAL_LCD_NOKIA_H_
#define HAL_LCD_NOKIA_H_

#define LCD_X 84
#define LCD_Y 6

#define LCD_CLK_SET HAL_GPIO_WritePin(LCD_CLK_GPIO_Port, LCD_CLK_Pin, GPIO_PIN_SET)
#define LCD_CLK_CLRHAL_GPIO_WritePin(LCD_CLK_GPIO_Port, LCD_CLK_Pin, GPIO_PIN_RESET)

#define LCD_DATA_SET HAL_GPIO_WritePin(LCD_DATA_GPIO_Port, LCD_DATA_Pin, GPIO_PIN_SET)
#define LCD_DATA_CLR HAL_GPIO_WritePin(LCD_DATA_GPIO_Port, LCD_DATA_Pin, GPIO_PIN_RESET)

#define LCD_DC_SET HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_SET)
#define LCD_DC_CLR HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_RESET)

#define LCD_CE_SET HAL_GPIO_WritePin(LCD_CE_GPIO_Port, LCD_CE_Pin, GPIO_PIN_SET)
#define LCD_CE_CLR HAL_GPIO_WritePin(LCD_CE_GPIO_Port, LCD_CE_Pin, GPIO_PIN_RESET)

#define LCD_RST_SET HAL_GPIO_WritePin(LCD_RST_GPIO_Port, LCD_RST_Pin, GPIO_PIN_SET)
#define LCD_RST_CLRHAL_GPIO_WritePin(LCD_RST_GPIO_Port, LCD_RST_Pin, GPIO_PIN_RESET)

#define LCD_CMD0
#define LCD_DATA 1

#define LCD_SETX 0x80
#define LCD_SETY 0x40

#define LCD_HOME lcd_write_byte(0, 0x40);lcd_write_byte(0, 0x80)
#define LCD_GOTO(x,y) lcd_write_byte(0, 0x40|(y));lcd_write_byte(0, 0x80|(x))



void lcd_init(void);
void lcd_clear(void);
void lcd_write_byte(unsigned char, unsigned char);
void lcd_text(char[], unsigned char, unsigned char);
void lcd_image(const unsigned char[], char, char, char, char);
void lcd_text(char[], unsigned char , unsigned char );
void lcd_scroll(unsigned char[], unsigned char, unsigned int);

#endif /* HAL_LCD_NOKIA_H_ */[/syntax]

Struktura projektu:
Obrazek

Efekt:
Obrazek

Statystyki: Napisane przez KosteQ95 — 4 paź 2016, o 14:32

]]> 2016-10-04T07:32:54+01:00 2016-10-04T07:32:54+01:00 https://forum.atnel.pl/viewtopic.php?t=16380&p=170368#p170368 <![CDATA[Re: Atollic TrueStudio implementacja własnej biblioteki lcd]]>
KosteQ95 napisał(a):

I tu wiąże się pytanie jak podpiąć własną bibliotekę pod linkowane pliki projektu z CubeMx
Nie bardzo wiem, o co ci chodzi? Przecież jeśli stworzysz nowy projekt w oparciu o HAL, to będzie on zawierał w sobie właściwe ścieżki. Twoja biblioteka nie powinna zawierać ścieżek bezwzględnych do HAL, czy też jakichkolwiek plików z tej biblioteki.

Statystyki: Napisane przez Sparrow-hawk — 4 paź 2016, o 07:32

]]> 2016-10-03T17:09:17+01:00 2016-10-03T17:09:17+01:00 https://forum.atnel.pl/viewtopic.php?t=16380&p=170334#p170334 <![CDATA[Atollic TrueStudio implementacja własnej biblioteki lcd]]>

Kod w jednym pliku prezentuje się tak:
[syntax=c]/**
******************************************************************************
* File Name : main.c
* Description : Main program body
******************************************************************************
*
* COPYRIGHT(c) 2016 STMicroelectronics
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"

/* USER CODE BEGIN Includes */
#define LCD_X 84
#define LCD_Y 6

#define LCD_CLK_SET HAL_GPIO_WritePin(LCD_CLK_GPIO_Port, LCD_CLK_Pin, GPIO_PIN_SET)
#define LCD_CLK_CLRHAL_GPIO_WritePin(LCD_CLK_GPIO_Port, LCD_CLK_Pin, GPIO_PIN_RESET)

#define LCD_DATA_SET HAL_GPIO_WritePin(LCD_DATA_GPIO_Port, LCD_DATA_Pin, GPIO_PIN_SET)
#define LCD_DATA_CLR HAL_GPIO_WritePin(LCD_DATA_GPIO_Port, LCD_DATA_Pin, GPIO_PIN_RESET)

#define LCD_DC_SET HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_SET)
#define LCD_DC_CLR HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_RESET)

#define LCD_CE_SET HAL_GPIO_WritePin(LCD_CE_GPIO_Port, LCD_CE_Pin, GPIO_PIN_SET)
#define LCD_CE_CLR HAL_GPIO_WritePin(LCD_CE_GPIO_Port, LCD_CE_Pin, GPIO_PIN_RESET)

#define LCD_RST_SET HAL_GPIO_WritePin(LCD_RST_GPIO_Port, LCD_RST_Pin, GPIO_PIN_SET)
#define LCD_RST_CLRHAL_GPIO_WritePin(LCD_RST_GPIO_Port, LCD_RST_Pin, GPIO_PIN_RESET)

#define LCD_CMD0
#define LCD_DATA 1

#define LCD_SETX 0x80
#define LCD_SETY 0x40

#define LCD_HOME lcd_write_byte(0, 0x40);lcd_write_byte(0, 0x80)
#define LCD_GOTO(x,y) lcd_write_byte(0, 0x40|(y));lcd_write_byte(0, 0x80|(x))
/* USER CODE END Includes */

/* Private variables ---------------------------------------------------------*/

/* USER CODE BEGIN PV */
/* Private variables ---------------------------------------------------------*/
unsigned char font[] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5f,0x00,0x00,0x00,0x00,0x07,0x00,0x07,
0x00,0x00,0x14,0x7f,0x14,0x7f,0x14,0x00,0x24,0x2a,0x7f,0x2a,0x12,0x00,0x23,0x13,
0x08,0x64,0x62,0x00,0x36,0x49,0x55,0x22,0x50,0x00,0x00,0x00,0x03,0x00,0x00,0x00,
0x00,0x1c,0x22,0x41,0x00,0x00,0x00,0x41,0x22,0x1c,0x00,0x00,0x14,0x08,0x3e,0x08,
0x14,0x00,0x08,0x08,0x3e,0x08,0x08,0x00,0x00,0x50,0x30,0x00,0x00,0x00,0x08,0x08,
0x08,0x08,0x08,0x00,0x00,0x60,0x60,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x00,
0x3e,0x51,0x49,0x45,0x3e,0x00,0x00,0x42,0x7f,0x40,0x00,0x00,0x42,0x61,0x51,0x49,
0x46,0x00,0x21,0x41,0x45,0x4b,0x31,0x00,0x18,0x14,0x12,0x7f,0x10,0x00,0x27,0x45,
0x45,0x45,0x39,0x00,0x3c,0x4a,0x49,0x49,0x30,0x00,0x03,0x71,0x09,0x05,0x03,0x00,
0x36,0x49,0x49,0x49,0x36,0x00,0x06,0x49,0x49,0x29,0x1e,0x00,0x00,0x36,0x36,0x00,
0x00,0x00,0x00,0x56,0x36,0x00,0x00,0x00,0x08,0x14,0x22,0x41,0x00,0x00,0x14,0x14,
0x14,0x14,0x14,0x00,0x00,0x41,0x22,0x14,0x08,0x00,0x02,0x01,0x51,0x09,0x06,0x00,
0x32,0x49,0x79,0x41,0x3e,0x00,0x7e,0x11,0x11,0x11,0x7e,0x00,0x7f,0x49,0x49,0x49,
0x36,0x00,0x3e,0x41,0x41,0x41,0x22,0x00,0x7f,0x41,0x41,0x41,0x3e,0x00,0x7f,0x49,
0x49,0x49,0x41,0x00,0x7f,0x09,0x09,0x09,0x01,0x00,0x3e,0x41,0x41,0x49,0x7a,0x00,
0x7f,0x08,0x08,0x08,0x7f,0x00,0x00,0x41,0x7f,0x41,0x00,0x00,0x20,0x40,0x41,0x3f,
0x01,0x00,0x7f,0x08,0x14,0x22,0x41,0x00,0x7f,0x40,0x40,0x40,0x40,0x00,0x7f,0x02,
0x0c,0x02,0x7f,0x00,0x7f,0x04,0x08,0x10,0x7f,0x00,0x3e,0x41,0x41,0x41,0x3e,0x00,
0x7f,0x09,0x09,0x09,0x06,0x00,0x3e,0x41,0x51,0x21,0x5e,0x00,0x7f,0x09,0x19,0x29,
0x46,0x00,0x46,0x49,0x49,0x49,0x31,0x00,0x01,0x01,0x7f,0x01,0x01,0x00,0x3f,0x40,
0x40,0x40,0x3f,0x00,0x1f,0x20,0x40,0x20,0x1f,0x00,0x3f,0x40,0x38,0x40,0x3f,0x00,
0x63,0x14,0x08,0x14,0x63,0x00,0x07,0x08,0x70,0x08,0x07,0x00,0x61,0x51,0x49,0x45,
0x43,0x00,0x00,0x7f,0x41,0x41,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x00,0x00,0x41,
0x41,0x7f,0x00,0x00,0x04,0x02,0x01,0x02,0x04,0x00,0x40,0x40,0x40,0x40,0x40,0x00,
0x00,0x01,0x02,0x04,0x00,0x00,0x20,0x54,0x54,0x54,0x78,0x00,0x7f,0x48,0x44,0x44,
0x38,0x00,0x38,0x44,0x44,0x44,0x20,0x00,0x38,0x44,0x44,0x48,0x7f,0x00,0x38,0x54,
0x54,0x54,0x18,0x00,0x08,0x7e,0x09,0x01,0x02,0x00,0x18,0xa4,0xa4,0xa4,0x7c,0x00,
0x7f,0x08,0x04,0x04,0x78,0x00,0x00,0x48,0x7d,0x40,0x00,0x00,0x00,0x00,0x84,0x7d,
0x00,0x00,0x7f,0x10,0x28,0x44,0x00,0x00,0x00,0x41,0x7f,0x40,0x00,0x00,0x7c,0x04,
0x78,0x04,0x78,0x00,0x7c,0x08,0x04,0x04,0x78,0x00,0x38,0x44,0x44,0x44,0x38,0x00,
0xfc,0x24,0x24,0x24,0x18,0x00,0x18,0x24,0x24,0x28,0xfc,0x00,0x7c,0x08,0x04,0x04,
0x08,0x00,0x48,0x54,0x54,0x54,0x20,0x00,0x04,0x3f,0x44,0x40,0x20,0x00,0x3c,0x40,
0x40,0x20,0x7c,0x00,0x1c,0x20,0x40,0x20,0x1c,0x00,0x3c,0x40,0x30,0x40,0x3c,0x00,
0x44,0x28,0x10,0x28,0x44,0x00,0x1c,0xa0,0xa0,0xa0,0x7c,0x00,0x44,0x64,0x54,0x4c,
0x44,0x00,0x00,0x08,0x36,0x41,0x00,0x00,0x00,0x00,0x7f,0x00,0x00,0x00,0x00,0x41,
0x36,0x08,0x00,0x00,0x10,0x08,0x08,0x10,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x20,0x54,0x54,0xd4,0x78,0x00,0x38,0x44,0x46,0x45,0x20,0x00,0x38,0x54,0x54,0xd4,
0x18,0x00,0x00,0x49,0x7f,0x44,0x00,0x00,0x7c,0x08,0x06,0x05,0x78,0x00,0x38,0x44,
0x46,0x45,0x38,0x00,0x48,0x54,0x56,0x55,0x20,0x00,0x44,0x64,0x56,0x4d,0x44,0x00,
0x44,0x64,0x55,0x4c,0x44,0x00,0x7e,0x11,0x11,0x91,0x7e,0x00,0x3c,0x42,0x46,0x43,
0x24,0x00,0x7f,0x49,0x49,0xc9,0x41,0x00,0x7f,0x50,0x48,0x44,0x40,0x00,0x7e,0x04,
0x0b,0x10,0x7e,0x00,0x3c,0x42,0x46,0x43,0x3c,0x00,0x4c,0x52,0x56,0x53,0x22,0x00,
0x42,0x66,0x53,0x4a,0x46,0x00,0x42,0x62,0x53,0x4a,0x46,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
void Error_Handler(void);
static void MX_GPIO_Init(void);

/* USER CODE BEGIN PFP */
/* Private function prototypes -----------------------------------------------*/

void lcd_init(void);
void lcd_clear(void);
void lcd_write_byte(unsigned char, unsigned char);
void lcd_text(char[], unsigned char, unsigned char);
void lcd_image(const unsigned char[], char, char, char, char);
void lcd_text(char[], unsigned char , unsigned char );
void lcd_scroll(unsigned char[], unsigned char, unsigned int);

/* USER CODE END PFP */

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

int main(void)
{

/* USER CODE BEGIN 1 */

/* USER CODE END 1 */

/* MCU Configuration----------------------------------------------------------*/

/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();

/* Configure the system clock */
SystemClock_Config();

/* Initialize all configured peripherals */
MX_GPIO_Init();

/* USER CODE BEGIN 2 */
lcd_init();
lcd_clear();

lcd_text("Programowanie", 3, 0);
lcd_text("Nucleo F446RE", 1*6, 1);
lcd_text("i wyświetlacz", 1*6, 3);
lcd_text("od Nokii 3310", 0*6, 4);
lcd_text("Pozdr KosteQ", 1*6, 5);

/* USER CODE END 2 */

/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
HAL_GPIO_TogglePin(LD2_GPIO_Port,LD2_Pin);
HAL_Delay(1000);
/* USER CODE END WHILE */

/* USER CODE BEGIN 3 */

}
/* USER CODE END 3 */

}

/** System Clock Configuration
*/
void SystemClock_Config(void)
{

RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;

__HAL_RCC_PWR_CLK_ENABLE();

__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = 16;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = 8;
RCC_OscInitStruct.PLL.PLLN = 180;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
RCC_OscInitStruct.PLL.PLLQ = 2;
RCC_OscInitStruct.PLL.PLLR = 2;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
Error_Handler();
}

if (HAL_PWREx_EnableOverDrive() != HAL_OK)
{
Error_Handler();
}

RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
{
Error_Handler();
}

HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);

HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);

/* SysTick_IRQn interrupt configuration */
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
}

/** Configure pins as
* Analog
* Input
* Output
* EVENT_OUT
* EXTI
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
static void MX_GPIO_Init(void)
{

GPIO_InitTypeDef GPIO_InitStruct;

/* GPIO Ports Clock Enable */
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOH_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();

/*Configure GPIO pin : BUTTON_Pin */
GPIO_InitStruct.Pin = BUTTON_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(BUTTON_GPIO_Port, &GPIO_InitStruct);

/*Configure GPIO pins : LCD_DC_Pin LCD_CE_Pin LCD_CLK_Pin LCD_DATA_Pin */
GPIO_InitStruct.Pin = LCD_DC_Pin|LCD_CE_Pin|LCD_CLK_Pin|LCD_DATA_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);

/*Configure GPIO pins : USART_TX_Pin USART_RX_Pin */
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

/*Configure GPIO pins : LCD_RST_Pin LD2_Pin */
GPIO_InitStruct.Pin = LCD_RST_Pin|LD2_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOC, LCD_DC_Pin|LCD_CE_Pin|LCD_CLK_Pin|LCD_DATA_Pin, GPIO_PIN_RESET);

/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOA, LCD_RST_Pin|LD2_Pin, GPIO_PIN_RESET);

/* EXTI interrupt init*/
HAL_NVIC_SetPriority(EXTI15_10_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(EXTI15_10_IRQn);

}

/* USER CODE BEGIN 4 */
void lcd_init(void){


LCD_RST_CLR;
HAL_Delay(20);
LCD_RST_SET;
LCD_CE_SET;
lcd_write_byte(LCD_CMD, 0x21); // Function set - extended instruction set
lcd_write_byte(LCD_CMD, 0x13); // Bias - 1:48
lcd_write_byte(LCD_CMD, 0x06); // Temperature Control
lcd_write_byte(LCD_CMD, 0xa5); // Set Vop
lcd_write_byte(LCD_CMD, 0x20); // Function set - basic instruction set, horizontal addressing
lcd_write_byte(LCD_CMD, 0x0C); // Display control - normal mode
}

void lcd_write_byte(unsigned char c_d, unsigned char data ){
unsigned char m;
LCD_CE_CLR;

if(c_d) LCD_DC_SET; else LCD_DC_CLR;

for(m=0x80; m; m>>=1)
{
if(data & m)
LCD_DATA_SET;
else
LCD_DATA_CLR;

LCD_CLK_SET;
for(int i=0; i<200; i++){

}
LCD_CLK_CLR;
}
LCD_CE_SET;
}

void lcd_image(const unsigned char s[],char x, char y, char w, char h){
unsigned int i,j,k;

for(i=0,j=0,k=0; i<h; i++)
{
lcd_write_byte(LCD_CMD, 0x40|(i+y));
lcd_write_byte(LCD_CMD, 0x80|(x));

for(j=0; j<w ; j++,k++){
lcd_write_byte(LCD_DATA, (s[k]));
}
}
}

void lcd_text(char s[], unsigned char x, unsigned char y)
{
unsigned int c,j;
unsigned char i,k;

// Kody polskich literek z ogonkami
char pl[] = {'ą','ć','ę','ł','ń','ó','ś','ź','ż','Ą','Ć','Ę','Ł','Ń','Ó','Ś','Ź','Ż'};

// Ustawia położenia pierwszej litery tekstu na ekranie LCD
lcd_write_byte(LCD_CMD, LCD_SETY|(y));
lcd_write_byte(LCD_CMD, LCD_SETX|(x));

// Rysuje znak po znaku
for(k=0; (c = s[k]); k++)
{
// Dopasowuje kody znaków z ogonkami
for(i=0; (i<18) && (pl[i]!=c); i++) ;
if(i<18) c= 0x80+i;

// Kopiuje jeden znak(6x8) z FLASH do pamięci obrazu LCD
for(i=0, j=(c-32)*6; i<6; i++,j++)
lcd_write_byte(LCD_DATA, (font[j]));
}
}

void lcd_clear(void){
unsigned char i,j;

LCD_HOME;

for(i=0; i<LCD_Y; i++)
{
LCD_GOTO(0, i);
for(j=0; j<LCD_X; j++)
lcd_write_byte(LCD_DATA, 0x00);
}

LCD_HOME;
}

void lcd_scroll(unsigned char txt[], unsigned char line, unsigned int czas)
{
unsigned int j,l,k,n,m;
unsigned char c,i;

// Kody polskich literek z ogonkami
unsigned char pl[] = {'ą','ć','ę','ł','ń','ó','ś','ź','ż','Ą','Ć','Ę','Ł','Ń','Ó','Ś','Ź','Ż'};

// liczenie znaków w tekście
for(n=0;(txt[n]);n++);

for(j=0; j<(n-(LCD_X/6))*6 ;j++)
{
LCD_GOTO(0, line);

for(i=0,l=j; i<LCD_X ;i++,l++)
{
c = (txt[ (l/6) ]);

// Dopasowuje kody polskich znaków z ogonkami
for( m=0; (m<18) && (pl[m]!=c); m++) ;
if(m<18) c= 0x80+m;

k = (c-32)*6+(l%6);

lcd_write_byte(LCD_DATA, (font[k]));
}
HAL_Delay(czas);
}
}


/* USER CODE END 4 */

/**
* @brief This function is executed in case of error occurrence.
* @param None
* @retval None
*/
void Error_Handler(void)
{
/* USER CODE BEGIN Error_Handler */
/* User can add his own implementation to report the HAL error return state */
while(1)
{
}
/* USER CODE END Error_Handler */
}

#ifdef USE_FULL_ASSERT

/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t* file, uint32_t line)
{
/* USER CODE BEGIN 6 */
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* USER CODE END 6 */

}

#endif

/**
* @}
*/

/**
* @}
*/

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/[/syntax]

A po przeniesieniu:
LCD.h:
[syntax=c]/*
* HAL_LCD_NOKIA.h
*
* Created on: Oct 3, 2016
* Author: KosteQ
*/

#ifndef HAL_LCD_NOKIA_H_
#define HAL_LCD_NOKIA_H_

#define LCD_X 84
#define LCD_Y 6

#define LCD_CLK_SET HAL_GPIO_WritePin(LCD_CLK_GPIO_Port, LCD_CLK_Pin, GPIO_PIN_SET)
#define LCD_CLK_CLRHAL_GPIO_WritePin(LCD_CLK_GPIO_Port, LCD_CLK_Pin, GPIO_PIN_RESET)

#define LCD_DATA_SET HAL_GPIO_WritePin(LCD_DATA_GPIO_Port, LCD_DATA_Pin, GPIO_PIN_SET)
#define LCD_DATA_CLR HAL_GPIO_WritePin(LCD_DATA_GPIO_Port, LCD_DATA_Pin, GPIO_PIN_RESET)

#define LCD_DC_SET HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_SET)
#define LCD_DC_CLR HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_RESET)

#define LCD_CE_SET HAL_GPIO_WritePin(LCD_CE_GPIO_Port, LCD_CE_Pin, GPIO_PIN_SET)
#define LCD_CE_CLR HAL_GPIO_WritePin(LCD_CE_GPIO_Port, LCD_CE_Pin, GPIO_PIN_RESET)

#define LCD_RST_SET HAL_GPIO_WritePin(LCD_RST_GPIO_Port, LCD_RST_Pin, GPIO_PIN_SET)
#define LCD_RST_CLRHAL_GPIO_WritePin(LCD_RST_GPIO_Port, LCD_RST_Pin, GPIO_PIN_RESET)

#define LCD_CMD0
#define LCD_DATA 1

#define LCD_HOME lcd_write_byte(0, 0x40);lcd_write_byte(0, 0x80)
#define LCD_GOTO(x,y) lcd_write_byte(0, 0x40|(y));lcd_write_byte(0, 0x80|(x))



void lcd_init(void);
void lcd_clear(void);
void lcd_write_byte(unsigned char, unsigned char);
void lcd_text(char[], unsigned char, unsigned char);
void lcd_image(const unsigned char[], char, char, char, char);
void lcd_text(char[], unsigned char , unsigned char );
void lcd_scroll(unsigned char[], unsigned char, unsigned int);

#endif /* HAL_LCD_NOKIA_H_ */[/syntax]

LCD.c:
[syntax=c]/*
* HAL_LCD_NOKIA.c
*
* Created on: Oct 3, 2016
* Author: KosteQ
*/


#include "HAL_LCD_NOKIA.h"


void lcd_init(void){


LCD_RST_CLR;
HAL_Delay(20);
LCD_RST_SET;
LCD_CE_SET;
lcd_write_byte(LCD_CMD, 0x21); // Function set - extended instruction set
lcd_write_byte(LCD_CMD, 0x13); // Bias - 1:48
lcd_write_byte(LCD_CMD, 0x06); // Temperature Control
lcd_write_byte(LCD_CMD, 0xa5); // Set Vop
lcd_write_byte(LCD_CMD, 0x20); // Function set - basic instruction set, horizontal addressing
lcd_write_byte(LCD_CMD, 0x0C); // Display control - normal mode
}

void lcd_write_byte(unsigned char c_d, unsigned char data ){
unsigned char m;
LCD_CE_CLR;

if(c_d) LCD_DC_SET; else LCD_DC_CLR;

for(m=0x80; m; m>>=1)
{
if(data & m)
LCD_DATA_SET;
else
LCD_DATA_CLR;

LCD_CLK_SET;
for(int i=0; i<200; i++){

}
LCD_CLK_CLR;
}
LCD_CE_SET;
}

void lcd_image(const unsigned char s[],char x, char y, char w, char h){
unsigned int i,j,k;

for(i=0,j=0,k=0; i<h; i++)
{
lcd_write_byte(LCD_CMD, 0x40|(i+y));
lcd_write_byte(LCD_CMD, 0x80|(x));

for(j=0; j<w ; j++,k++){
lcd_write_byte(LCD_DATA, (s[k]));
}
}
}

void lcd_text(char s[], unsigned char x, unsigned char y)
{
unsigned int c,j;
unsigned char i,k;

// Kody polskich literek z ogonkami
char pl[] = {'ą','ć','ę','ł','ń','ó','ś','ź','ż','Ą','Ć','Ę','Ł','Ń','Ó','Ś','Ź','Ż'};

// Ustawia położenia pierwszej litery tekstu na ekranie LCD
lcd_write_byte(LCD_CMD, LCD_SETY|(y));
lcd_write_byte(LCD_CMD, LCD_SETX|(x));

// Rysuje znak po znaku
for(k=0; (c = s[k]); k++)
{
// Dopasowuje kody znaków z ogonkami
for(i=0; (i<18) && (pl[i]!=c); i++) ;
if(i<18) c= 0x80+i;

// Kopiuje jeden znak(6x8) z FLASH do pamięci obrazu LCD
for(i=0, j=(c-32)*6; i<6; i++,j++)
lcd_write_byte(LCD_DATA, (font[j]));
}
}

void lcd_clear(void){
unsigned char i,j;

LCD_HOME;

for(i=0; i<LCD_Y; i++)
{
LCD_GOTO(0, i);
for(j=0; j<LCD_X; j++)
lcd_write_byte(LCD_DATA, 0x00);
}

LCD_HOME;
}

void lcd_scroll(unsigned char txt[], unsigned char line, unsigned int czas)
{
unsigned int j,l,k,n;
unsigned char c,i;

// Kody polskich literek z ogonkami
unsigned char pl[] = {'ą','ć','ę','ł','ń','ó','ś','ź','ż','Ą','Ć','Ę','Ł','Ń','Ó','Ś','Ź','Ż'};

// liczenie znaków w tekście
for(n=0;(txt[n]);n++);

for(j=0; j<(n-(LCD_X/6))*6 ;j++)
{
LCD_GOTO(0, line);

for(i=0,l=j; i<LCD_X ;i++,l++)
{
c = (txt[ (l/6) ]);

// Dopasowuje kody polskich znaków z ogonkami
for(m=0; (m<18) && (pl[m]!=c); m++) ;
if(m<18) c= 0x80+m;

k = (c-32)*6+(l%6);

lcd_write_byte(LCD_DATA, (font[k]));
}
delay_ms(czas);
}
}[/syntax]

Plik main:
[syntax=c]/**
******************************************************************************
* File Name : main.c
* Description : Main program body
******************************************************************************
*
* COPYRIGHT(c) 2016 STMicroelectronics
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"

/* USER CODE BEGIN Includes */
#include "HAL_LCD_NOKIA.h"
/* USER CODE END Includes */

/* Private variables ---------------------------------------------------------*/

/* USER CODE BEGIN PV */
/* Private variables ---------------------------------------------------------*/
unsigned char font[] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5f,0x00,0x00,0x00,0x00,0x07,0x00,0x07,
0x00,0x00,0x14,0x7f,0x14,0x7f,0x14,0x00,0x24,0x2a,0x7f,0x2a,0x12,0x00,0x23,0x13,
0x08,0x64,0x62,0x00,0x36,0x49,0x55,0x22,0x50,0x00,0x00,0x00,0x03,0x00,0x00,0x00,
0x00,0x1c,0x22,0x41,0x00,0x00,0x00,0x41,0x22,0x1c,0x00,0x00,0x14,0x08,0x3e,0x08,
0x14,0x00,0x08,0x08,0x3e,0x08,0x08,0x00,0x00,0x50,0x30,0x00,0x00,0x00,0x08,0x08,
0x08,0x08,0x08,0x00,0x00,0x60,0x60,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x00,
0x3e,0x51,0x49,0x45,0x3e,0x00,0x00,0x42,0x7f,0x40,0x00,0x00,0x42,0x61,0x51,0x49,
0x46,0x00,0x21,0x41,0x45,0x4b,0x31,0x00,0x18,0x14,0x12,0x7f,0x10,0x00,0x27,0x45,
0x45,0x45,0x39,0x00,0x3c,0x4a,0x49,0x49,0x30,0x00,0x03,0x71,0x09,0x05,0x03,0x00,
0x36,0x49,0x49,0x49,0x36,0x00,0x06,0x49,0x49,0x29,0x1e,0x00,0x00,0x36,0x36,0x00,
0x00,0x00,0x00,0x56,0x36,0x00,0x00,0x00,0x08,0x14,0x22,0x41,0x00,0x00,0x14,0x14,
0x14,0x14,0x14,0x00,0x00,0x41,0x22,0x14,0x08,0x00,0x02,0x01,0x51,0x09,0x06,0x00,
0x32,0x49,0x79,0x41,0x3e,0x00,0x7e,0x11,0x11,0x11,0x7e,0x00,0x7f,0x49,0x49,0x49,
0x36,0x00,0x3e,0x41,0x41,0x41,0x22,0x00,0x7f,0x41,0x41,0x41,0x3e,0x00,0x7f,0x49,
0x49,0x49,0x41,0x00,0x7f,0x09,0x09,0x09,0x01,0x00,0x3e,0x41,0x41,0x49,0x7a,0x00,
0x7f,0x08,0x08,0x08,0x7f,0x00,0x00,0x41,0x7f,0x41,0x00,0x00,0x20,0x40,0x41,0x3f,
0x01,0x00,0x7f,0x08,0x14,0x22,0x41,0x00,0x7f,0x40,0x40,0x40,0x40,0x00,0x7f,0x02,
0x0c,0x02,0x7f,0x00,0x7f,0x04,0x08,0x10,0x7f,0x00,0x3e,0x41,0x41,0x41,0x3e,0x00,
0x7f,0x09,0x09,0x09,0x06,0x00,0x3e,0x41,0x51,0x21,0x5e,0x00,0x7f,0x09,0x19,0x29,
0x46,0x00,0x46,0x49,0x49,0x49,0x31,0x00,0x01,0x01,0x7f,0x01,0x01,0x00,0x3f,0x40,
0x40,0x40,0x3f,0x00,0x1f,0x20,0x40,0x20,0x1f,0x00,0x3f,0x40,0x38,0x40,0x3f,0x00,
0x63,0x14,0x08,0x14,0x63,0x00,0x07,0x08,0x70,0x08,0x07,0x00,0x61,0x51,0x49,0x45,
0x43,0x00,0x00,0x7f,0x41,0x41,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x00,0x00,0x41,
0x41,0x7f,0x00,0x00,0x04,0x02,0x01,0x02,0x04,0x00,0x40,0x40,0x40,0x40,0x40,0x00,
0x00,0x01,0x02,0x04,0x00,0x00,0x20,0x54,0x54,0x54,0x78,0x00,0x7f,0x48,0x44,0x44,
0x38,0x00,0x38,0x44,0x44,0x44,0x20,0x00,0x38,0x44,0x44,0x48,0x7f,0x00,0x38,0x54,
0x54,0x54,0x18,0x00,0x08,0x7e,0x09,0x01,0x02,0x00,0x18,0xa4,0xa4,0xa4,0x7c,0x00,
0x7f,0x08,0x04,0x04,0x78,0x00,0x00,0x48,0x7d,0x40,0x00,0x00,0x00,0x00,0x84,0x7d,
0x00,0x00,0x7f,0x10,0x28,0x44,0x00,0x00,0x00,0x41,0x7f,0x40,0x00,0x00,0x7c,0x04,
0x78,0x04,0x78,0x00,0x7c,0x08,0x04,0x04,0x78,0x00,0x38,0x44,0x44,0x44,0x38,0x00,
0xfc,0x24,0x24,0x24,0x18,0x00,0x18,0x24,0x24,0x28,0xfc,0x00,0x7c,0x08,0x04,0x04,
0x08,0x00,0x48,0x54,0x54,0x54,0x20,0x00,0x04,0x3f,0x44,0x40,0x20,0x00,0x3c,0x40,
0x40,0x20,0x7c,0x00,0x1c,0x20,0x40,0x20,0x1c,0x00,0x3c,0x40,0x30,0x40,0x3c,0x00,
0x44,0x28,0x10,0x28,0x44,0x00,0x1c,0xa0,0xa0,0xa0,0x7c,0x00,0x44,0x64,0x54,0x4c,
0x44,0x00,0x00,0x08,0x36,0x41,0x00,0x00,0x00,0x00,0x7f,0x00,0x00,0x00,0x00,0x41,
0x36,0x08,0x00,0x00,0x10,0x08,0x08,0x10,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x20,0x54,0x54,0xd4,0x78,0x00,0x38,0x44,0x46,0x45,0x20,0x00,0x38,0x54,0x54,0xd4,
0x18,0x00,0x00,0x49,0x7f,0x44,0x00,0x00,0x7c,0x08,0x06,0x05,0x78,0x00,0x38,0x44,
0x46,0x45,0x38,0x00,0x48,0x54,0x56,0x55,0x20,0x00,0x44,0x64,0x56,0x4d,0x44,0x00,
0x44,0x64,0x55,0x4c,0x44,0x00,0x7e,0x11,0x11,0x91,0x7e,0x00,0x3c,0x42,0x46,0x43,
0x24,0x00,0x7f,0x49,0x49,0xc9,0x41,0x00,0x7f,0x50,0x48,0x44,0x40,0x00,0x7e,0x04,
0x0b,0x10,0x7e,0x00,0x3c,0x42,0x46,0x43,0x3c,0x00,0x4c,0x52,0x56,0x53,0x22,0x00,
0x42,0x66,0x53,0x4a,0x46,0x00,0x42,0x62,0x53,0x4a,0x46,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};
/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
void Error_Handler(void);
static void MX_GPIO_Init(void);

/* USER CODE BEGIN PFP */
/* Private function prototypes -----------------------------------------------*/

/* USER CODE END PFP */

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

int main(void)
{

/* USER CODE BEGIN 1 */

/* USER CODE END 1 */

/* MCU Configuration----------------------------------------------------------*/

/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();

/* Configure the system clock */
SystemClock_Config();

/* Initialize all configured peripherals */
MX_GPIO_Init();

/* USER CODE BEGIN 2 */
lcd_init();
lcd_clear();

lcd_text("Programowanie", 3, 0);
lcd_text("Nucleo F446RE", 1*6, 1);
lcd_text("i wyświetlacz", 1*6, 3);
lcd_text("od Nokii 3310", 0*6, 4);
lcd_text("Pozdr KosteQ", 1*6, 5);

/* USER CODE END 2 */

/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
HAL_GPIO_TogglePin(LD2_GPIO_Port,LD2_Pin);
HAL_Delay(1000);
/* USER CODE END WHILE */

/* USER CODE BEGIN 3 */

}
/* USER CODE END 3 */

}

/** System Clock Configuration
*/
void SystemClock_Config(void)
{

RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;

__HAL_RCC_PWR_CLK_ENABLE();

__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = 16;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = 8;
RCC_OscInitStruct.PLL.PLLN = 180;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
RCC_OscInitStruct.PLL.PLLQ = 2;
RCC_OscInitStruct.PLL.PLLR = 2;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
Error_Handler();
}

if (HAL_PWREx_EnableOverDrive() != HAL_OK)
{
Error_Handler();
}

RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
{
Error_Handler();
}

HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);

HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);

/* SysTick_IRQn interrupt configuration */
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
}

/** Configure pins as
* Analog
* Input
* Output
* EVENT_OUT
* EXTI
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
static void MX_GPIO_Init(void)
{

GPIO_InitTypeDef GPIO_InitStruct;

/* GPIO Ports Clock Enable */
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOH_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();

/*Configure GPIO pin : BUTTON_Pin */
GPIO_InitStruct.Pin = BUTTON_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(BUTTON_GPIO_Port, &GPIO_InitStruct);

/*Configure GPIO pins : LCD_DC_Pin LCD_CE_Pin LCD_CLK_Pin LCD_DATA_Pin */
GPIO_InitStruct.Pin = LCD_DC_Pin|LCD_CE_Pin|LCD_CLK_Pin|LCD_DATA_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);

/*Configure GPIO pins : USART_TX_Pin USART_RX_Pin */
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

/*Configure GPIO pins : LCD_RST_Pin LD2_Pin */
GPIO_InitStruct.Pin = LCD_RST_Pin|LD2_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOC, LCD_DC_Pin|LCD_CE_Pin|LCD_CLK_Pin|LCD_DATA_Pin, GPIO_PIN_RESET);

/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOA, LCD_RST_Pin|LD2_Pin, GPIO_PIN_RESET);

/* EXTI interrupt init*/
HAL_NVIC_SetPriority(EXTI15_10_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(EXTI15_10_IRQn);

}

/* USER CODE BEGIN 4 */

/* USER CODE END 4 */

/**
* @brief This function is executed in case of error occurrence.
* @param None
* @retval None
*/
void Error_Handler(void)
{
/* USER CODE BEGIN Error_Handler */
/* User can add his own implementation to report the HAL error return state */
while(1)
{
}
/* USER CODE END Error_Handler */
}

#ifdef USE_FULL_ASSERT

/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t* file, uint32_t line)
{
/* USER CODE BEGIN 6 */
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* USER CODE END 6 */

}

#endif

/**
* @}
*/

/**
* @}
*/

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/[/syntax]


Pliki bibloteki znajdują się w folderze inc plik h a w src plik c

Statystyki: Napisane przez KosteQ95 — 3 paź 2016, o 17:09

]]>